1. Brief introduction
1. FC30 UAV long endurance hovering
Ground station continuously provides drone-power electricity for 8 hours of hovering which enables clean / spray work can last long
2. Multiple ways to supply power
25kw max. 380V industrial power supply, generator power supply.
3. High security
Installation replacing one of the original battery packs. If emergency, the backup battery pack can immediately take over the power supply.
2. Highlights
1. The system retains only the input switch, high-voltage switch and cable-recovery knob, which is simple to operate and can be rapidly deployed. Users only need to operate the drone, which can greatly improve operational efficiency and safety;
2. The product is integrated, high power density, miniaturized, lightweight, modular and intelligent design, easy to move and carry;
3. The on-board power supply adopts voltage regulator circuit scheme, wide range input, constant voltage regulator output, continuous and stable power supply (the backup battery is only used for safe forced landing, and can be configured to have enough capacity for safe landing), which breaks through the limitation of the flight duration;
4. The power supply in the base station adopts isolation circuit design to ensure the safety of high-voltage power transmission.
3. System composition
1. FC30 DJI drone
2. Payload system
3. FC30T Onboard Power Supply together with 240m Tethered Base Station
4. 380V min.25kw power by customers
4. Detailed parameters
DJI Drone
DJI FC30 drone, parameters and configurations are detailed on the DJI website
Tethered system
Integrated Ground Tethered Base Station
Performance indicators
1.1. Environmental characteristics
1. Equipment Operation Procedure
1. Check that the equipment is complete: Check that the main body of the drone, the cleaning device, the control system and the guards are intact.
2. Install the cleaning device: Install the cleaning device to the main body of the drone and make sure it is firmly connected.
3. Connect the power supply: Connect the battery to the remote control and turn on the power switch.
4. Control the drone flight: Use the remote control to control the drone flight, adjust the flight height, speed and direction as needed.
5. Start cleaning: After determining the cleaning object, switch on the cleaning pump and use the drone to clean the target.
2. Equipment Maintenance
Daily maintenance: after each use, the main body of the drone and the cleaning device should be cleaned to keep the equipment clean and tidy. At the same time, check whether there is any damage or looseness of the parts and deal with them in time.
Regular Maintenance: It is recommended to carry out a comprehensive equipment inspection and maintenance once a month, including replacing worn parts and cleaning the internal circuit boards.
3. Principles of use
1. When in use, the power supply should maintain good ventilation and heat dissipation; the air passage of the module unit should not be blocked;
2. The power supply should be used under the environmental conditions specified in the specification;
3. Do not adjust the potentiometer in the power supply at will;
4. Do not operate in the presence of volatile gases or flammable environments;
5. Do not remove the outer cover or touch the internal parts under any circumstances;
6. For safety reasons, do not perform internal warranty or parts replacement alone;
7. The power supply must be safely insulated when in use, and any side of it must be at least 8mm away from the outer metal shell; if it is less than 8mm, a PVC sheet with a thickness of more than 1mm must be used to strengthen the insulation;
8. If you notice smoke or unpleasant odor during startup or use, turn off the power immediately.
4. Warranty
The warranty period for this product is 1 year. During the warranty period, any natural damage under normal use will be repaired free of charge by our company;
However, if any of the following conditions occur, the warranty will not apply:
1. Damage caused by unauthorized repair without the permission of the company;
2. Any addition or modification;
3. Improper operation or use;
4. Abnormal environmental conditions, exceeding specification requirements, causing damage;
5. Deliberate human damage;
6. Damage caused by force majeure natural disasters.
5. Repair scope
If the power supply fails to operate normally during the warranty period due to errors in materials or manufacturing technology, our company will provide free repair or replacement. The repair service will include various labor services and any necessary adjustments or replacement parts.
6. Restrictions
1. If you fail to pack the product in the same way as when you send it back and it is damaged during transportation, the warranty will also be void.
2. Our company will not be responsible for any of the following:
Damage caused by fire, earthquake, riot, war, terrorist attack, third party's behavior and other events;
Damage caused by the customer's intentional or negligent act, misuse, or use under other abnormal conditions;
Incidental damages arising from the use or performance of this product [interruption of business, loss of business profits (including loss of use of equipment, costs of replacing any equipment, devices or services, or claims by your customers)];
Any damage caused by using the method other than that specified in this manual;
Regardless of any circumstances, such as operation, cleaning or maintenance, please be sure to comply with the safety rules stipulated in Item 7. If you violate them and cause safety concerns beyond the original design and manufacturing, our company will not be responsible.
--DRONE SOLUTION PROVIDER--
MYUAV TECHNOLOGIES CO.,LTD.
Tax No.:91320118MA275YW43M LegalRegister No.:320125000443821
Add:No.89，Pingliang Street，Jianye District, Nanjing,China 210019
M:MYUAV9@MYUAV.com.cn T:+86 17898801662 W:en.MYUAV.com.cn
[Caution]MYUAV is a manufacturer of defense products and is under security management by a state agency.